9. You can select print-quality options in the following ways: In the Windows driver dialog: go to the Paper/Quality tab and look at the Print Quality section. 10. Front-panel message Suggested action Sheet too big During the load process the printer has detected that the sheet of paper is either too wide or too long to be loaded correctly. Copyright 2017 HP Development Company, L.P. Contact HP Support (see Contact HP Support on page 188). Clean the original and the scanners glass plate, then scan again. 
See Contact HP Support on page 188. 2.
When you see the message, you should contact HP Support (see Contact HP Support on page 188) and request the maintenance kit.
NOTE: This printer is not designed to use continuous ink systems. Close the door and follow the instructions on the front panel. The file format is incorrect or not supported. If copying, set the content type to IMAGE. If your hair is long, try to secure it so that it will not fall into the equipment. Mechanical hazard The equipment has moving parts that could cause injury. Lines are discontinuous If your lines are broken in the following way: ENWW 1. Click Done. CAUTION: Observe precautions when handling the printhead, because it is an ESD-sensitive device (see the Glossary on page 194). var s=iw[ce]('script');s.async='async';s.defer='defer';s.charset='utf-8';s.src=wp+"//jsc.mgid.com/t/a/tailieuvan.vn.243064.js?t="+D.getYear()+D.getMonth()+D.getUTCDate()+D.getUTCHours();c[ac](s);})(); Phn tch tm trng v hnh ng ca nhn vt M | Lm vn mu, So snh nhn vt Trng v A Ph | Lm vn mu, Bi th Ty Tin c phng pht nhng nt bun | Lm vn mu, Ni kht khao sng kht khao hnh phc gia nh | Vn mu, Mi ngn bt l mt dng cm nhn c sc ca tng tc gi | Vn mu, Gi tr hin thc v nhn o trong tc phm V Nht | Vn mu, Cm nhn v bi kch b tha ha ca Trng Ba | Lm vn mu, Cm nhn v p khut lp ca nhn vt ngi n b hng chi | Vn mu, M nghe ting so vng li thit tha bi hi | Lm vn mu, Cm hng lng mn v bi trng trong bi th Ty Tin | Lm vn mu, Bn v nhn vt Trng trong truyn ngn V nht | Lm vn mu, So snh nhn vt M vi ngi n b hng chi | Vn mu, So snh nhn vt M vi nhn vt ngi v nht | Vn mu, So snh ngh thut xy dng hai nhn vt M v A Ph | Vn mu, So snh hnh nh on qun Ty Tin v Vit Bc | Vn mu, Phn tch nhn vt Phng nh trong Nhng ngi sao xa xi | Vn mu, Phn tch nhn vt anh thanh nin trong Lng l Sapa, Phn tch nhn vt ng Hai trong tc phm Lng, Phn tch nhn vt lo Hc trong truyn ngn cng tn ca Nam Cao, Phn tch nhn vt ch Du trong on trch Tc nc v b, Qu khch khng cho tr em tin bnh ko | Lm vn mu, So snh v p nhn vt ngi anh hng Tn vi v p ca A Ph | Vn mu, Cm nhn v p ca nhn vt ngi v nht v ngi n b hng chi | Vn mu, V p con sng qua Ai t tn cho dng sng v Ngi li sng | Vn mu, Phn tch nhn vt ngi li v Hun Cao | Lm vn mu, So snh truyn ngn Ch Pho v V nht | Lm vn mu. The following examples show this defect: original on the left, printed image on the right. Print from Autodesk AutoCAD 1. TigerDirect Business is not responsible for typographical or photographic errors. Choose from the available paper sizes. Sorry, you need to enable JavaScript to visit this website. Original settings Content type Lighter/darker allows you to adjust the lightness of the copy. Copyright 2022 TigerDirect Business. Clipping in dark or light areas Sometimes you may see that the scanned file or copy of one of your plots has lost detail in light or dark areas (or both), as in the example below: original on the left, scanned image on the right. Close the ink cartridge cover. Click Options. To view our discounted price, simply click the Lowest Price Tag in the product details page or add the item to your shopping cart. Touch Start Scan to start the process. Note that there is a black ring near the center of pattern F. In this step, you must look at the region near the black ring.
In the Color tab, the default color management option is Printer managed colors, and this is the correct option because you have already selected Printer Manages Colors in Photoshop. Look for the Scan to computer option, then select Webscan. 8. 2. Only one of these methods can be used at a time, and switching from one to another is manual: it is not done automatically. Return to default calibration Returning to the default calibration sets all the corrections made by the paper advance calibration to zero. 3. Creating and using firewall rules Firewall rules allow you to control IP traffic. 20 Troubleshooting data communication issues Communication failures between computer and printer Wired network issues Wireless network issues Mobile printing and web services issues The network configuration page 174 Chapter 20 Troubleshooting data communication issues ENWW. HP-GL/2, HP-RTL, TIFF, JPEG, CALS G4, HP PCL 3 GUI, URF, Power consumption User name should contain the name of the 'scanner user'. Printhead door 5. This item is covered by Newegg.com's Replacement Only Return Policy. 21 Troubleshooting general printer issues ENWW The printer does not start The printer does not print The printer seems slow The front panel is frozen Cannot access the Embedded Web Server Alerts 181. Check that there is no space between the roll and the stops at both ends. CAUTION: Do not move the paper sideways, as it could damage the printer. 3. From the HP Utility: You can access the Embedded Web Server through the HP Utility. 7. 7. Ensure that the paper is far enough inside the printer, you should feel the printer grab the paper. You can disable the cutter, see Turn the automatic cutter on and off on page 40. If the mail server requires authentication, email notifications will not work. Print from USB flash drive 1. Windows a. Click Start, point to Settings, then click Printers or Printers and Faxes. Using a USB flash drive: 1. The blue stop can be removed to mount a new roll; it slides along the spindle to hold rolls of different widths. The scanner will automatically grab the sheet and move it into position for scanning. 90 2. If the problem persists, analyze pattern D of the diagnostic plot. 6. The following information is displayed on the front panel: Paper type you have selected Roll or sheet status Width of the paper in millimeters (estimated) If no roll or no single-sheet paper is loaded, or there is no paper in the multi sheet tray, the message Status: Not ready and Out of paper is displayed. Guillotines are valuable equipment, which can be utilised just about anywhere where paper needs to be cut accurately with very little effort. 2. The printer automatically attempts to straighten the paper. 7. If the problem persists, proceed to analyze the following areas of the diagnostic plot: D, H and L (for three modules, 0-Left, 1-Middle, and 2-Right and its intersection) If you see any of these defects in the studied areas, call HP support and report a line discontinuities error after calibration. Actions 1.
You can also scan from your smartphone or tablet: See Mobile printing and Web Services on page 12 for more information. There are a few limitations that you should bear in mind: ENWW The attached files to be printed must be in PDF, JPEG, or TIFF formats. 5. NOTE: The maximum length of paper that the scanner can scan depends on the paper width, among other options such as scan resolution. 2. 6. Matte paper categories from thinnest to thickest are: Plain Paper Coated Paper Heavyweight Coated Paper For other image quality problems, see Troubleshooting print-quality issues on page 136. See Printing on page 41 for alternative ways of printing. Keep up to date with all Neopost related News & Events. Check that the paper type selected in the front panel is the same as the paper type you are using. You will now see file sharing enabled and Windows sharing on. Click File > Print, and select the name of your printer. Check the Share this folder box. |Model#:F9A29A#B1K, ListPrice: $3,895.00Cents$3,895.00$Price: $3,895.003,895.00. Open the roll cover. 80 2.
If this happens: 1. Then select the paper on which the diagnostic plot is going to be printed (you can reuse the diagnostic plot at any time in the future, if it is saved carefully). Vertical lines of different colors If your print has vertical bands of different colors along it: 1. Eject and reload the calibration sheet, checking that it is clean, in good condition, face up and perfectly centered in the scanner. This printer is loaded with USB 2.0, Gigabit Ethernet RJ 45 Port and Wireless LAN for wireless printing. 5 x 5 x 5 x 5 mm, Guaranteed minimum line width 1. Printer settings > Webscan from EWS.
inks are used to compose the gray shades. You can also select the color settings. Then highlight that line.
Move the print-quality slider to the extreme left ('Speed'). Darkness Define the file settings fields for files scanned to the network folder. 4.
The front bottom area (between the scanner platen and front window) Using your fingers, you can turn the rubber wheels to get better access to the paper and clear any debris. Close the lid. Lines are blurred Humidity can cause ink to soak into the paper, making the lines blurred and fuzzy. Reconnect the printer's power cable, turn on the power switch at the rear, and turn on the printer using the power key. 3. A strip stays on the output tray and generates jams If a small piece of paper has been cut, such as before printing a new roll, or after the front panel option Form feed and cut has been used, the cut strip may remain in the output tray. Automatic firmware update The printer can automatically check for a firmware update periodically (see Firmware update on page 107). Grain Looking at patterns A, B, and C, you may find problems in the printers paper advance or the printheads that cause visible grain in area fills. If not, call HP support and report an incorrect paper advance error. Wide prints make more efficient use of ink than narrow prints, because printhead maintenance uses some ink, and its frequency is related to the number of passes made by the printhead. Ink cartridge cover 4. You do not need to unload the roll and spindle to load a single sheet. Touch the Save Form button. Khi c tc p[]. If you are not using a unique network name (SSID), then it is possible that your computer could be connected to a nearby network that is not yours. Use photo if in doubt. 5. 4. If the roll is long, rest the spindle horizontally on a table and load the roll on the table. Blueprint for copying blueprint originals with optimum results. This printer easily fits your business and reduces time for easy and convenient printing, so go buy the HP Designjet T730 Inkjet Large Format Printer now! 4. Firewall policy pages are accessed through the Embedded Web Server and displayed by your Web browser. Under the Settings tab, look for Webscan from EWS and make sure it is enabled. 15 Troubleshooting print-quality issues General printing advice Horizontal lines across the image (banding) Lines are too thick, too thin, or missing Lines appear stepped or jagged Lines print double or in the wrong colors Lines are discontinuous Lines are blurred Line lengths are inaccurate The whole image is blurry or grainy The paper is not flat The print is scuffed or scratched Ink marks on the paper Black ink comes off when you touch the print Edg. That is, the limits between two strong colors are not well defined or a third color appears between them. 10. 6 ENWW Printing Print from USB flash drive Mobile printing Print with HP Click Print from a computer using a printer driver Advanced print settings Color management 41. Carefully remove any of the jammed paper that you can lift up and out from the top of the printer. Mobile printing You can print to your printer from many mobile devices and from almost any location. HP DesignJet T730 Printer rear view 1. 2. Before you begin, check your equipment: The printer should be set up and on. Do not attempt to straighten the paper during the aligning process, unless instructed to do so by the frontpanel display. ENWW Do not push your fingers inside the printer's paper path. Mechanical accuracy 0.1% of the specified vector length or 0.2 mm (whichever is greater) at 23C (73F), 50-60% relative humidity, on E/A0 printing material in Best or Normal mode with HP Heavyweight Coated Paper feed. Flare in the image when scanning glossy originals If the scanner is miscalibrated, or if the original plot you are trying to scan is very glossy or reflective, you can sometimes find flare in the scanned image, as in the following example: original on the left, scanned image on the right. Click File > Print, and select the name of your printer. endstream endobj 29 0 obj <>stream 2. If you find an error message on the front panel during this operation, call HP support and report the error message. Pull out the tray. 9. Open the top window. Ink cartridge A removable printer component that stores ink of a particular color and provides it to the printhead. HP Designjet T730 Inkjet Large Format Printer 14. Sheet too small During the load process the printer detected that the sheet of paper is too narrow or too short to be loaded in the printer. An alert is displayed if the maximum length is exceeded. Drills, Staplers and other finishing accessories that will fit into any print production environment. Insert the tubes connector into the printhead. 11. var s=iw[ce]('script');s.async='async';s.defer='defer';s.charset='utf-8';s.src=wp+"//jsc.mgid.com/t/a/tailieuvan.vn.264917.js?t="+D.getYear()+D.getMonth()+D.getUTCDate()+D.getUTCHours();c[ac](s);})(); (function(){ Output platen 9. Scanner cover 11. When the system has restarted, repeat the calibration. NOTE: ENWW The page size will not be automatically selected according to the document size. Select the Layout/Output tab, then select Autorotate. This setting will apply to jobs that do not contain any printer emulation setting saved in the job. Configure network settings You can view and configure the network settings from the Embedded Web Server, the HP Utility or the front panel. For further information on settings go to Scan to network setup process on page 60. In this case, you must give the email address(es) to which the scanned job will be sent. From the front panel: swipe down the dashboard, touch Network setup. If in doubt, clean the scanner and restart the calibration process. In the Forms tab, check the Create a new form box. Bin 8. Your computer or printer hangs (stays idle), while communication is taking place. Check that you have the correct type of cartridge (model number). See our latest range of product catalogues. A correct example is given below, followed by two incorrect examples. The front panel also displays alerts (warning and error messages) when needed. General printing advice When you have any print-quality problem: To achieve the best performance from your printer, use only genuine manufacturer's supplies and accessories, whose reliability and performance have been thoroughly tested to give trouble-free performance and best-quality prints. Output platen 9. tFos|-l5nZGa1.9p4BsWeU4d%pcAv|aXgxhNEHqhd8(tq$& n|xfl&qXf1o?7`s"&*+6Hv8*HL&XY :A*8a*es Bi lm After printing, the paper has wrinkles or there is too much ink This happens when too much ink is used. Prices and specifications are subject to change without notice. If it is a copy, repeat it, setting the content type to Image. Remove all paper from the tray. Feed the paper into the printer. Name Product number HP DesignJet 36-in Spindle B3Q37A HP DesignJet 24-in Spindle B3Q36A Introduction to the accessories HP DesignJet 36-in Spindle (for 36-in printers) With extra spindles, you can change rapidly from one paper type to another. Reload the roll, or load a new sheet; see Paper handling on page 31. ENWW 3. 78 0 obj <>stream 2. If your printer is a T830 1. ENWW Carefully remove any of the jammed paper that you can from the front window. Open the top window. From the front panel, swipe down the dashboard and touch advance calibration > Reset ready paper calibration. Protect, enhance and preserve your printed material using our range of high-quality Laminators, Roll Films and Laminating Pouches. If you still cannot find your paper type in the whole list, see The paper type is not in the driver on page 119. A new printhead has been inserted without a new set of ink cartridges. These innovative & versatile printers produce elegantly and accurately printed envelopes to enhance your mailings. If any of the colored blocks in Test Pattern 2 show white lines, or are faded or completely missing, clean the printhead (see Clean the printhead on page 100). Touch OK when ready. The four vertical thin black lines at the beginning and the end of the diagnostic plot show, approximately, the position of the intersection between scanbars, where this kind of error usually appears.
See Contact HP Support on page 188. 2. When you see the message, you should contact HP Support (see Contact HP Support on page 188) and request the maintenance kit.
NOTE: This printer is not designed to use continuous ink systems. Close the door and follow the instructions on the front panel. The file format is incorrect or not supported. If copying, set the content type to IMAGE. If your hair is long, try to secure it so that it will not fall into the equipment. Mechanical hazard The equipment has moving parts that could cause injury. Lines are discontinuous If your lines are broken in the following way: ENWW 1. Click Done. CAUTION: Observe precautions when handling the printhead, because it is an ESD-sensitive device (see the Glossary on page 194). var s=iw[ce]('script');s.async='async';s.defer='defer';s.charset='utf-8';s.src=wp+"//jsc.mgid.com/t/a/tailieuvan.vn.243064.js?t="+D.getYear()+D.getMonth()+D.getUTCDate()+D.getUTCHours();c[ac](s);})(); Phn tch tm trng v hnh ng ca nhn vt M | Lm vn mu, So snh nhn vt Trng v A Ph | Lm vn mu, Bi th Ty Tin c phng pht nhng nt bun | Lm vn mu, Ni kht khao sng kht khao hnh phc gia nh | Vn mu, Mi ngn bt l mt dng cm nhn c sc ca tng tc gi | Vn mu, Gi tr hin thc v nhn o trong tc phm V Nht | Vn mu, Cm nhn v bi kch b tha ha ca Trng Ba | Lm vn mu, Cm nhn v p khut lp ca nhn vt ngi n b hng chi | Vn mu, M nghe ting so vng li thit tha bi hi | Lm vn mu, Cm hng lng mn v bi trng trong bi th Ty Tin | Lm vn mu, Bn v nhn vt Trng trong truyn ngn V nht | Lm vn mu, So snh nhn vt M vi ngi n b hng chi | Vn mu, So snh nhn vt M vi nhn vt ngi v nht | Vn mu, So snh ngh thut xy dng hai nhn vt M v A Ph | Vn mu, So snh hnh nh on qun Ty Tin v Vit Bc | Vn mu, Phn tch nhn vt Phng nh trong Nhng ngi sao xa xi | Vn mu, Phn tch nhn vt anh thanh nin trong Lng l Sapa, Phn tch nhn vt ng Hai trong tc phm Lng, Phn tch nhn vt lo Hc trong truyn ngn cng tn ca Nam Cao, Phn tch nhn vt ch Du trong on trch Tc nc v b, Qu khch khng cho tr em tin bnh ko | Lm vn mu, So snh v p nhn vt ngi anh hng Tn vi v p ca A Ph | Vn mu, Cm nhn v p ca nhn vt ngi v nht v ngi n b hng chi | Vn mu, V p con sng qua Ai t tn cho dng sng v Ngi li sng | Vn mu, Phn tch nhn vt ngi li v Hun Cao | Lm vn mu, So snh truyn ngn Ch Pho v V nht | Lm vn mu. The following examples show this defect: original on the left, printed image on the right. Print from Autodesk AutoCAD 1. TigerDirect Business is not responsible for typographical or photographic errors. Choose from the available paper sizes. Sorry, you need to enable JavaScript to visit this website. Original settings Content type Lighter/darker allows you to adjust the lightness of the copy. Copyright 2022 TigerDirect Business. Clipping in dark or light areas Sometimes you may see that the scanned file or copy of one of your plots has lost detail in light or dark areas (or both), as in the example below: original on the left, scanned image on the right. Close the ink cartridge cover. Click Options. To view our discounted price, simply click the Lowest Price Tag in the product details page or add the item to your shopping cart. Touch Start Scan to start the process. Note that there is a black ring near the center of pattern F. In this step, you must look at the region near the black ring.
In the Color tab, the default color management option is Printer managed colors, and this is the correct option because you have already selected Printer Manages Colors in Photoshop. Look for the Scan to computer option, then select Webscan. 8. 2. Only one of these methods can be used at a time, and switching from one to another is manual: it is not done automatically. Return to default calibration Returning to the default calibration sets all the corrections made by the paper advance calibration to zero. 3. Creating and using firewall rules Firewall rules allow you to control IP traffic. 20 Troubleshooting data communication issues Communication failures between computer and printer Wired network issues Wireless network issues Mobile printing and web services issues The network configuration page 174 Chapter 20 Troubleshooting data communication issues ENWW. HP-GL/2, HP-RTL, TIFF, JPEG, CALS G4, HP PCL 3 GUI, URF, Power consumption User name should contain the name of the 'scanner user'. Printhead door 5. This item is covered by Newegg.com's Replacement Only Return Policy. 21 Troubleshooting general printer issues ENWW The printer does not start The printer does not print The printer seems slow The front panel is frozen Cannot access the Embedded Web Server Alerts 181. Check that there is no space between the roll and the stops at both ends. CAUTION: Do not move the paper sideways, as it could damage the printer. 3. From the HP Utility: You can access the Embedded Web Server through the HP Utility. 7. 7. Ensure that the paper is far enough inside the printer, you should feel the printer grab the paper. You can disable the cutter, see Turn the automatic cutter on and off on page 40. If the mail server requires authentication, email notifications will not work. Print from USB flash drive 1. Windows a. Click Start, point to Settings, then click Printers or Printers and Faxes. Using a USB flash drive: 1. The blue stop can be removed to mount a new roll; it slides along the spindle to hold rolls of different widths. The scanner will automatically grab the sheet and move it into position for scanning. 90 2. If the problem persists, analyze pattern D of the diagnostic plot. 6. The following information is displayed on the front panel: Paper type you have selected Roll or sheet status Width of the paper in millimeters (estimated) If no roll or no single-sheet paper is loaded, or there is no paper in the multi sheet tray, the message Status: Not ready and Out of paper is displayed. Guillotines are valuable equipment, which can be utilised just about anywhere where paper needs to be cut accurately with very little effort. 2. The printer automatically attempts to straighten the paper. 7. If the problem persists, proceed to analyze the following areas of the diagnostic plot: D, H and L (for three modules, 0-Left, 1-Middle, and 2-Right and its intersection) If you see any of these defects in the studied areas, call HP support and report a line discontinuities error after calibration. Actions 1.
You can also scan from your smartphone or tablet: See Mobile printing and Web Services on page 12 for more information. There are a few limitations that you should bear in mind: ENWW The attached files to be printed must be in PDF, JPEG, or TIFF formats. 5. NOTE: The maximum length of paper that the scanner can scan depends on the paper width, among other options such as scan resolution. 2. 6. Matte paper categories from thinnest to thickest are: Plain Paper Coated Paper Heavyweight Coated Paper For other image quality problems, see Troubleshooting print-quality issues on page 136. See Printing on page 41 for alternative ways of printing. Keep up to date with all Neopost related News & Events. Check that the paper type selected in the front panel is the same as the paper type you are using. You will now see file sharing enabled and Windows sharing on. Click File > Print, and select the name of your printer. Check the Share this folder box. |Model#:F9A29A#B1K, ListPrice: $3,895.00Cents$3,895.00$Price: $3,895.003,895.00. Open the roll cover. 80 2. If this happens: 1. Then select the paper on which the diagnostic plot is going to be printed (you can reuse the diagnostic plot at any time in the future, if it is saved carefully). Vertical lines of different colors If your print has vertical bands of different colors along it: 1. Eject and reload the calibration sheet, checking that it is clean, in good condition, face up and perfectly centered in the scanner. This printer is loaded with USB 2.0, Gigabit Ethernet RJ 45 Port and Wireless LAN for wireless printing. 5 x 5 x 5 x 5 mm, Guaranteed minimum line width 1. Printer settings > Webscan from EWS.
inks are used to compose the gray shades. You can also select the color settings. Then highlight that line.
Move the print-quality slider to the extreme left ('Speed'). Darkness Define the file settings fields for files scanned to the network folder. 4.
The front bottom area (between the scanner platen and front window) Using your fingers, you can turn the rubber wheels to get better access to the paper and clear any debris. Close the lid. Lines are blurred Humidity can cause ink to soak into the paper, making the lines blurred and fuzzy. Reconnect the printer's power cable, turn on the power switch at the rear, and turn on the printer using the power key. 3. A strip stays on the output tray and generates jams If a small piece of paper has been cut, such as before printing a new roll, or after the front panel option Form feed and cut has been used, the cut strip may remain in the output tray. Automatic firmware update The printer can automatically check for a firmware update periodically (see Firmware update on page 107). Grain Looking at patterns A, B, and C, you may find problems in the printers paper advance or the printheads that cause visible grain in area fills. If not, call HP support and report an incorrect paper advance error. Wide prints make more efficient use of ink than narrow prints, because printhead maintenance uses some ink, and its frequency is related to the number of passes made by the printhead. Ink cartridge cover 4. You do not need to unload the roll and spindle to load a single sheet. Touch the Save Form button. Khi c tc p[]. If you are not using a unique network name (SSID), then it is possible that your computer could be connected to a nearby network that is not yours. Use photo if in doubt. 5. 4. If the roll is long, rest the spindle horizontally on a table and load the roll on the table. Blueprint for copying blueprint originals with optimum results. This printer easily fits your business and reduces time for easy and convenient printing, so go buy the HP Designjet T730 Inkjet Large Format Printer now! 4. Firewall policy pages are accessed through the Embedded Web Server and displayed by your Web browser. Under the Settings tab, look for Webscan from EWS and make sure it is enabled. 15 Troubleshooting print-quality issues General printing advice Horizontal lines across the image (banding) Lines are too thick, too thin, or missing Lines appear stepped or jagged Lines print double or in the wrong colors Lines are discontinuous Lines are blurred Line lengths are inaccurate The whole image is blurry or grainy The paper is not flat The print is scuffed or scratched Ink marks on the paper Black ink comes off when you touch the print Edg. That is, the limits between two strong colors are not well defined or a third color appears between them. 10. 6 ENWW Printing Print from USB flash drive Mobile printing Print with HP Click Print from a computer using a printer driver Advanced print settings Color management 41. Carefully remove any of the jammed paper that you can lift up and out from the top of the printer. Mobile printing You can print to your printer from many mobile devices and from almost any location. HP DesignJet T730 Printer rear view 1. 2. Before you begin, check your equipment: The printer should be set up and on. Do not attempt to straighten the paper during the aligning process, unless instructed to do so by the frontpanel display. ENWW Do not push your fingers inside the printer's paper path. Mechanical accuracy 0.1% of the specified vector length or 0.2 mm (whichever is greater) at 23C (73F), 50-60% relative humidity, on E/A0 printing material in Best or Normal mode with HP Heavyweight Coated Paper feed. Flare in the image when scanning glossy originals If the scanner is miscalibrated, or if the original plot you are trying to scan is very glossy or reflective, you can sometimes find flare in the scanned image, as in the following example: original on the left, scanned image on the right. Click File > Print, and select the name of your printer. endstream endobj 29 0 obj <>stream 2. If you find an error message on the front panel during this operation, call HP support and report the error message. Pull out the tray. 9. Open the top window. Ink cartridge A removable printer component that stores ink of a particular color and provides it to the printhead. HP Designjet T730 Inkjet Large Format Printer 14. Sheet too small During the load process the printer detected that the sheet of paper is too narrow or too short to be loaded in the printer. An alert is displayed if the maximum length is exceeded. Drills, Staplers and other finishing accessories that will fit into any print production environment. Insert the tubes connector into the printhead. 11. var s=iw[ce]('script');s.async='async';s.defer='defer';s.charset='utf-8';s.src=wp+"//jsc.mgid.com/t/a/tailieuvan.vn.264917.js?t="+D.getYear()+D.getMonth()+D.getUTCDate()+D.getUTCHours();c[ac](s);})(); (function(){ Output platen 9. Scanner cover 11. When the system has restarted, repeat the calibration. NOTE: ENWW The page size will not be automatically selected according to the document size. Select the Layout/Output tab, then select Autorotate. This setting will apply to jobs that do not contain any printer emulation setting saved in the job. Configure network settings You can view and configure the network settings from the Embedded Web Server, the HP Utility or the front panel. For further information on settings go to Scan to network setup process on page 60. In this case, you must give the email address(es) to which the scanned job will be sent. From the front panel: swipe down the dashboard, touch Network setup. If in doubt, clean the scanner and restart the calibration process. In the Forms tab, check the Create a new form box. Bin 8. Your computer or printer hangs (stays idle), while communication is taking place. Check that you have the correct type of cartridge (model number). See our latest range of product catalogues. A correct example is given below, followed by two incorrect examples. The front panel also displays alerts (warning and error messages) when needed. General printing advice When you have any print-quality problem: To achieve the best performance from your printer, use only genuine manufacturer's supplies and accessories, whose reliability and performance have been thoroughly tested to give trouble-free performance and best-quality prints. Output platen 9. tFos|-l5nZGa1.9p4BsWeU4d%pcAv|aXgxhNEHqhd8(tq$& n|xfl&qXf1o?7`s"&*+6Hv8*HL&XY :A*8a*es Bi lm After printing, the paper has wrinkles or there is too much ink This happens when too much ink is used. Prices and specifications are subject to change without notice. If it is a copy, repeat it, setting the content type to Image. Remove all paper from the tray. Feed the paper into the printer. Name Product number HP DesignJet 36-in Spindle B3Q37A HP DesignJet 24-in Spindle B3Q36A Introduction to the accessories HP DesignJet 36-in Spindle (for 36-in printers) With extra spindles, you can change rapidly from one paper type to another. Reload the roll, or load a new sheet; see Paper handling on page 31. ENWW 3. 78 0 obj <>stream 2. If your printer is a T830 1. ENWW Carefully remove any of the jammed paper that you can from the front window. Open the top window. From the front panel, swipe down the dashboard and touch advance calibration > Reset ready paper calibration. Protect, enhance and preserve your printed material using our range of high-quality Laminators, Roll Films and Laminating Pouches. If you still cannot find your paper type in the whole list, see The paper type is not in the driver on page 119. A new printhead has been inserted without a new set of ink cartridges. These innovative & versatile printers produce elegantly and accurately printed envelopes to enhance your mailings. If any of the colored blocks in Test Pattern 2 show white lines, or are faded or completely missing, clean the printhead (see Clean the printhead on page 100). Touch OK when ready. The four vertical thin black lines at the beginning and the end of the diagnostic plot show, approximately, the position of the intersection between scanbars, where this kind of error usually appears.