The main power lamp will light up.
The lightest and heaviest combinations, according to EPTA-Procedure 01/2014, are shown in the table. for tightness. While holding the switch lever, push the drive lever forward and hold it to drive the rear wheels.
Inspect moving parts for damage, breakage, and wear.
Discoloration, deformation, or cracks may result. The cut grass may also block up inside of the lower body. To decrease the speed, pull the lever toward you, and to increase the speed, turn the lever forward. Firmly tighten 4 bolts which were temporarily tightened in step 1 using box wrench 13.
WARNING: Wear gloves when performing inspection or maintenance.
They may differ from country to country.
NOTE: The mower does not start without pressing the switch button even the switch lever is pulled.
Depending on the conditions of the lawn or the ground, the actual lawn height may become slightly different from the set height.NOTE: Try a test mowing of grass in a less conspicuous place to get your desired height. Main power lamp 5.
Soft no-load mode lamp 2. WARNING: Install the mower blade carefully.
Depending on the conditions inside of the basket, this indicator may not work properly. Lower handle 3. Mode switching button 4. Operation of the machine in a partially assembled state may result in serious personal injury from accidental start-up. 
If you need any assistance for more details regarding these accessories, ask your local Makita Service Center.
Electric brake This machine is equipped with an electric brake. Align the holes in the lower handle with the holes in the lower body, and then tighten 4 bolts temporarily. Ask your local authorized service center for repair.
The weight may differ depending on the attachment(s), including the battery cartridge. If the cord is damaged, the mower switch may not work. NOTE: This indicator is a rough guide. 
CAUTION: Before removing the bolts, hold the upper handle firmly. Install the portable power pack to the machine as shown in the figure. Constant speed control of blade rotation Electronic speed control for obtaining constant speed.
The term battery or battery cartridge in this instruction manual refers to the followings: WARNING: When using electric lawnmowers, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury; including the following. NOTE: The indicator lamp for the remaining battery capacity is just for reference.
Put the mower on its side so that the mowing height adjusting lever comes to the upper side. Mowing width 2.
Release the switch button as soon as the motor starts running. When you press the mode switching button again, the machine shifts to the noise reduction mode, and the noise reduction mode lamp lights up in green.
Before asking for repairs, conduct your own inspection first.
Store the lock key in a safe place out of reach of children. Be thoroughly familiar with the controls and the proper use of the mower before starting.
Failure to remove the lock key and the battery cartridge may result in serious personal injury from accidental start-up.
WARNING: The blade coasts for a few seconds after releasing the switch. Open the rear cover and take out the grass basket by holding the handle. NOTE: The mowing height figures should be used just as a guideline. Adjust the handle height, and then tighten the upper and lower bolts firmly.
To avoid unintentional start-up, the main power switch will automatically shut down when the switch lever and drive lever (if equipped) are not pulled for a certain period after the main power switch is turned on. The machine is equipped with electronic functions for easy operation.
Your email address will not be published.
Over-discharge protectionWhen the battery capacity is not enough, the machine stops automatically, the main power lamp blinks in red, and the indicator lamp lights up. It will also void the Makita warranty for the Makita tool and charger.
Front grip. Pour water toward the bottom of the machine to which the blade is attached. Use of any other portable power packs may cause injury and/or fire.
To install the mower blades, perform the removal procedure in reverse.
Pull the switch lever toward you while holding down the switch button.
The drive system does not work correctly.
When the machine is turned on, the machine starts up in the normal mode.When you press the mode switching button, the machine shifts to the soft no-load mode, and the soft no-load mode lamp lights up in green.
If an annexed warranty sheet is not available, refer to the warranty details set forth below website for your respective country.
If recharging is not effective, replace the battery. WARNING: Tighten the bolt clockwise firmly to secure the blade.
Make sure that all the clips are securely attached to the frame.
Store mower indoors in a cool, dry, and locked place.
Hold the handle of the grass basket, and then hook the grass basket on the rod of the lower body as shown in the figure. Open the right side cover, and then attach the discharge attachment. The traveling speed can be adjusted with the speed lever.
Failure to hold them firmly may cause them to slip off your hands and result in damage to the machine and portable power pack and a personal injury.
Release the drive lever and the switch lever to stop the machine.
Do not try to cut long grass all at once.
NOTE: Some items in the list may be included in the product package as standard accessories. Overlapping area 3.
Portable power pack to which battery cartridges are installed, Battery cartridge which is installed to the portable power pack. Then turn the machine on to restart. The use of any other accessories or attachments might present a risk of injury to persons. Change the mowing direction each time to prevent the grass grain pattern from forming in just one direction.
Align the hole in the lower handle with the hole in the upper handle, then insert the bolt from inside, and then tighten the nut from outside with box wrench 13.
Using the center lines as guidelines, mow in strips. To lock the blade, insert the pin into a hole on the lowerbody. CAUTION: If the cut grass or foreign object blocks up inside of the mower body, be sure to remove the lock key and battery cartridge and wear gloves before removing the grass or foreign object. WARNING: Always wear safety goggles or safety glasses with side shields when performing inspection or maintenance. The table below shows the relationship between the number on the mower body and the approximate mowing height.
Clean grass clippings accumulated on the underside of the mower deck.
Remove the mulching plug while holding down the lever. Install the portable power pack to the machine as shown in the figure. The mulching plug allows you to return the cut grass to the ground without gathering the cut grass in the grass basket. Mowing height adjusting lever 2.
Turn the bolt counterclockwise with box wrench 17.
Possible to get the fine finish, because the rotating speed is kept constant even under load conditions. The mowing height can be adjusted in the range of between 32 mm (1-1/4) and 100 mm (3-15/16).Remove the lock key, and then pull the mowing height adjusting lever outward of the lower body and move it to your desired mowing height. WARNING: Make sure that the mower blade and all the fixing parts are installed correctly and tightened securely.
1. Noise reduction mode lamp 3.
Hold the front grip or the lower handle with one hand, and then move the mowing height adjusting lever with the other hand. Instead, mow the lawn in steps.
Read All InstructionsRead, understand, and follow all instructions on the mower and in the instruction manuals.
Press the power button on the portable power pack.
It has a top/bottom face.
CAUTION: Before the operation, make sure that the cord is securely attached to the card holders and the socket is inserted into the plug all the way.
Overlap by one-half to one-third the previous strip to mow the lawn evenly.
NOTE: If the main power lamp lights up in red or blinks in red or green, refer to the instructions for the machine/battery protection system.NOTE: This machine employs the auto power-off function.
In this case, remove the battery from the machine and charge the battery or charge the battery to fully charged ones. Install the portable power pack, and then insert the lock key.
Only use accessory or attachment for its stated purpose.
Insert the frame into the grass basket as far as it will go. The machine is equipped with a machine/battery protection system.
WARNING: Never put your hand or leg under the mower body when adjusting the mowing height.
NOTICE: When using the machine with the mulching plug, make sure that the total length of grass after cutting is 30 mm (1-3/16) or more, and the cut length is 15 mm (9/16) or less. Instead, ask Makita Authorized Service Centers, always using Makita replacement parts for repairs. Before every periodical check, be sure to stop the mower then remove the lock key and the battery cartridge. In this case, let the machine and battery cool before turning the machine on again. WARNING: Always wear safety goggles or safety glasses with side shields when operating the mower.
Otherwise, the handle may fall and cause an injury.The handle height can be adjusted in two levels.
To turn off the machine, press the main power switch again.
WARNING: Before mowing, clear away sticks and stones from the mowing area.
Perform the same procedure on the other side.
Mode switching buttonYou can switch the operating mode by pressing the mode switching button. NOTICE: When installing handles, position the cords so that they are not caught by anything between the handles.
WARNING: Always remove the lock key when the mower is not in use.
Put the mower on its side so that the mowing height adjusting lever comes to the upper side. This system automatically cuts off power to the motor to extend machine and battery life.
Attach the cord to the cord holders as shown in the figure. Remove the bolt, and then the mower blade. WARNING: When you replace the blades, always follow the instructions provided in this manual.
NOTE: Mower may not start due to the overload when you try to mow long or dense grass at a time.
Tips for maintaining maximum battery life. To remove the grass basket, open the rear cover, and then remove the grass basket by holding the handle. Open the lock key cover, then insert the lock key in the place shown in the figure as far as it will go, and then close the lock key cover. Attach all the clips to the frame as shown in the figure. Abnormal vibration: stop the mower immediately!
If the machine consistently fails to quickly stop the mower blades after releasing the switch lever, have the machine serviced at Makita Authorized Service Center.
To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. Check all nuts, bolts, screws, etc. Dont store the mower and charger in locations where the temperature may reach or exceed 40 C (104 F). CAUTION: Only use genuine Makita batteries.Use of non-genuine Makita batteries, or batteries that have been altered, may result in the battery bursting causing fires, personal injury, and damage.
If not, it may accidentally fall out of the machine, causing injury to you or someone around you. If you notice anything unusual with either of the lock key or switch, stop the operation immediately and have them checked by your nearest Makita Authorized Service Center. Main power switch. Remove the lock key and battery cartridges, and then close the battery cover.
In this case, stop the operation immediately and empty the basket.
NOTE: Mowing long grass to a short length all at once may cause the grass to die. on makita CML01 Battery Powered Lawn Mower Instruction Manual, Important safety instructions for battery cartridge, Installing or removing the portable power pack, Indicating the remaining battery capacity, makita XAD05 Cordless Angle Drill Instruction Manual, makita UD2500 Electric Garden Shredder 2500W 45mm Instruction Manual, KOMPLETT PRO TECH 51cm Battery Powered Lawn Mower Instruction Manual, greenworks Optimow 4 Robot Lawn Mower User Guide, JBL Battery-Powered Lavalier Microphone User Guide, Srichpk P36A-Black Smart Watch User Manual, Shanghai Laisi Information Technology 2021AG Smart Rope User Manual, Pocket Juice Wireless Charging Power Bank User Manual, PHILIPS 439P1 Brilliance 4K Ultra HD Business Monitor User Guide, MARZAN SECURITY Electronic Lock with Keypad Round User Manual, ZERFUN G8 Pro Wireless Microphone System User Manual, Airrex Infrared Heater AH-200/300/800 User Manual, 2017 Toyota Camry Hybrid LE Fuse Box Diagrams, 2017 Mitsubishi Lancer 4WD Fuse Box Diagrams, Mitsubishi Lancer Passenger and Engine Fuse Box Diagram, Mira Honesty ERD Bar Valve and Fittings User Manual, Part number of the replacement mower blade, L: 1,630 mm to 1,715 mm (64 to 67-1/2) W: 590 mm (23-1/4).
CAUTION: Always switch off the machine before installing or removing the portable power pack.
The centerlines of the front wheels are guidelines for mowing width.
If you find a problem that is not explained in the manual, do not attempt to disassemble the machine. WARNING: The use of this product can create dust-containing chemicals which may cause respiratory or other illnesses.
Periodically check the grass basket for mowed grass.
To install the grass basket, follow the steps below.
When you operate the machine with the mulching plug, be sure to remove the grass basket.
Comment document.getElementById("comment").setAttribute("id","ac16cd2fda4c31028761c6f9dd01b496");document.getElementById("afe6277d1c").setAttribute("id","comment"); Save my name, email, and website in this browser for the next time I comment. WARNING: Always be sure that the lock key and battery cartridge are removed before carrying out any work on the mower. CAUTION: Hold the machine and the portable power pack firmly when installing or removing the portable power pack. Lock the locking levers on both sides of the portable power pack. The motor stops running after a little use.
Failure to remove the lock key and battery cartridge may cause a serious injury.
The followings show the symbols used for tool. WARNING: Only use the portable power packs listed above. WARNING: Before installing the battery cartridge, always check to see that the switch lever actuates properly and returns to the original position when released.
Empty the grass before it becomes full.
(1) 30 mm (1-3/16) or more (2) 15 mm (9/16) or less.
Attach the cord to the cord holders as shown in the figure.
The actual battery capacity may differ depending on the usage conditions. Please refer to the annexed warranty sheet for the most current warranty terms applicable to this product. Damaged or missing parts should be repaired or replaced.
Open the plug cover, then align the arrow insert the socket into the plug all the way. When you operate the machine with the discharge attachment, be sure to install the mulching plug and remove the grass basket. Remove the upper bolts of the lower handle using box wrench 13, and then loosen the lower bolts.
To remove the portable power pack, perform the installation procedure in reverse. Open the plug cover, then align the arrow mark on the socket with that on the machine, and then insert the socket into the plug all the way. Specifications may differ from country to country. 1.
WARNING: Always turn off the main power switch when not in use. NOTICE: Using the mower with the grass basket full prevents smooth blade rotation and places an extra load on the motor, which may cause a breakdown. Increase the mowing height in this case.
For PDC01NOTE: Before installing the portable power pack to the machine, install at least one battery to battery port 1 or 2, and at least one battery to battery port 3 or 4.
Some examples of these chemicals are compounds found in pesticides, insecticides, fertilizers, and herbicides.Your risk from these exposures varies, depending on how often you do this type of work. 1.
The blade is imbalanced, excessively, or unevenly worn.
The machine will automatically stop during operation if the machine or battery is placed under one of the fol- lowing conditions: Overload protectionWhen the battery is operated in a manner that causes it to draw an abnormally high current, the machine automatically stops and the main power lamp blinks in green.
Store the mower in a safe place out of the reach of children. When the grass basket is almost full, the indicator does not float while the blades are running. Centerline. Operating the machine with a switch that does not actuate properly can lead to loss of control and serious personal injury. NOTICE: When installing the mower blade, make sure that the protrusions on the blade support fit in the holes in the mower blade.
CAUTION: Make sure that the portable power pack is securely installed on the machine.
The control panel has the main power switch and the mode switching button.
The grass level indicator shows the volume of mowed grass. WARNING: Always be sure that the lock key and battery cartridge are removed from the mower before storing or carrying the mower or attempting to perform inspection or maintenance. Replace the grass basket if necessary. Attach the mulching plug while holding down the lever, and then release the lever to lock the mulching plug. The discharge attachment allows you to discharge the cut grass to the ground from the right side of the machine without gathering the cut grass in the grass basket. WARNING: Always remove the lock key and battery cartridge when removing or installing the blade.
Mower blade does not rotate: stop the mower immediately! Do not start any operation until the blade comes to a complete stop.
To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles. Do not mow weeds with this machine. NOTE: The display of the indicator lamp is updated when the machine stops operation.
To turn on the machine, press the main power switch.The main power lamp lights up in green. When the remaining battery capacity becomes low, the indicator lamp blinks or lights up.
In the soft no-load mode, you can minimize start-up shock.
Home Makita makita CML01 Battery Powered Lawn Mower Instruction Manual, INSTRUCTION MANUALBattery Powered Lawn MowerCML01.
CAUTION: These accessories or attachments are recommended for use with your Makita machine specified in this manual.
When the grass basket is not full, the indicator floats while the blades are running. Install the battery as described in this manual.
WARNING: To reduce the risk of accident, regularly check the grass basket for any damage or weakened strength.
Furthermore, clear away any weeds from the mowing area in advance.
Open the rear cover, and then remove the grass basket. Due to our continuing program of research and development, the specifications herein are subject to change without notice. In the noise reduction mode, you can decrease the noise at mowing.When you press the mode switching button again, the machine returns to the normal mode.
In this situation, turn the machine off and stop the application that caused the machine to become overloaded. Recharge the battery.
Firmly hold the handle with both hands when mowing.The mowing speed guideline is approximately 7 to 14 meters (23 46 ft.) per 10 seconds.
Leave a day or two between mowings until the lawn becomes evenly short.
WARNING: Never start the mower unless it is completely assembled.
NOTICE: Use this machine for mowing lawns only. Release the switch lever and drive lever.
Place the cord of the portable power pack as shown in the figure. NOTICE: After installing the mower blades, remove the pin from the lower body. This mower is equipped with a lock key and handle switch. When carrying the mower, hold the front grip and rear grip with two people as shown in the figure.